Services

• Specialty Services

• Appraisels $30–90
  Price varies with the degree of documentation desired and the rarity of the firearm
• Borescope Bore/Chamber/Muzzle $30–60
  Price is per barrel and depends on the type of firearm.
• Custom 10/22 Rifles
• Custom Rifles Based On REM 700 Actions $1500–5000
  Long range shooter to your taste
• Firearm Safety Inspection $30
• Firearms Transfers $20–30
  Plus actual cost of shipping for outgoing items
• Internet Consignment Sales
  10% of sales price (including broker fees) or $30, whichever is greater.
• Jeweling
• Rifle Or Revolver Complete Refinish $120–400
  Varies with condition and desired outcome, ie "make it shoot" or "make it pretty again"
• Test Fire Pistols/Revolver In A Ransom Rest $40
  need 2 weeks warning to order grip mold. Cost does not include ammunition cost.
• Winchester 70 Receiver Accurizing $175–250

• General Services

• Aftermarket Part Installation $40–250
• Boresight $15
• Complete Clean And Inspection $55
• Field Strip Clean $30–45
  Extra for very dirty or leaded barrels
• Fire Lapping $60
  Price does not include materials.
• Re Tip Firing Pin $25–35
• Recrown Muzzle $30–65
• Remove Stuck Empty Shell $20–40
• Removing Stuck Screws $10–40
  varies with extent of damage of screw and size, cost per hole or screw
• Scope Base Leveling $25
• Scope Mounting $25
• Scope Mounting With Drilling And Tapping $20–40
  Holes are priced individually.
• Scope Ring Lapping $25
• Swivel Installation Includes Basic Swivel Stud Per Hole $20

• Trigger Work

• 1911 2 3 Lbs+ $125
• 1911 3 4 Lbs+ $90
• 1911 4 Lbs+ $65
• Double Action Striker Fired $35
• Install Dayton Traister, Moyer, Shilen, Or Timney Trigger $45
• Install Jewell Trigger $25
• Install Winchester Mod 70 Trigger $90
• Other Firearms $45
• Revolver Trigger Tune $45–90
  Rate varies slightly with make and model. Taurus on the low end, Colt on the high. Materials extra...spring kits run about 16.00.MIM parts can only be smoothed and lightened a bit
• Rifle <2 Lbs $125
• Rifle <3 Lbs $90
• Rifle Or Shotgun $65

• Refinishing

• Abrasive Blasting Matte Unfinished And Left Stripped $100
• Cerakote Air Dry Coating $100–120
  Slightly less durable than the oven baked, but much easier to apply. Stripping charges may apply
• Cerakoting H Igh Temp $130–220
  Single color, add 60.00 for additional color and masking
• Cold Blue Touch Up $30
  I can blend and cover small areas with cold bluing. This does a good job at covering wear marks and scrathes.

• Handgun Work Semi Auto

• Adjust Magazine Lips $25
• Blowback Smoothing/Tuning $90
• Colored Front Sight Insert Installation $35
• Correct Loose Breech $135
• Cut Slide For Heine, Bomar Or Similar Rear, W/O Sight $97–130
  Extra charge for non-standard model gun fitting and adjustment
• Cut Slide Rear For Novak Style Sight, W/O Sight $65–95
  Some models may be more based on fitting required
• Dehorn And Break Edges $115
• Double Action Striker Fired Smoothing/Tuning $90
• Install Ambidextrous Safety $45
• Install Compensator $45–225
  Varies with model and type of compensator, refinishing not included
• Install Fiber Optic Front Sight $75
• Install Insert On Sight $45
• Install Or Adjust Magazine Catch $35
• Install Spring Kit $35
• Install Thumb Safety $40
• Polish And Smooth Breech Face $35
• Refitting Existing Dovetail And Install Front Sight, W/O Sight $30–45
  Range based on either no sight installed or removing staked stight.
• Undercut Trigger Guard $45

• Glock Pistol

• Install Aftermarket Barrel $35
• Install Fulcrum Trigger $75
• Install Manual Safety $40

• Springfield Xd Pistol

• Install Aftermarket Barrel $40
• Install Sights $35

• Browning Hi Power Pistol

• Install Cylinder And Slide Hammer $45
• Install Cylinder And Slide Sear Lever $55
• Install Spring Kit $40
• Trigger Work $90

• Colt 1911 Style

• 1911 Smoothing/Tuning $160
• 4 Pt. Accurizing Process. Custom Fit Barrel Bushing, Minimize Slide Play And Smooth, Polish Feed Ramp And Lighten Trigger. $200–250
  I can test shoot this in a ransom rest to prove it out
• Bevel 1911 Magazine Well $45
• Install 1911 Drop In Barrel $45
• Install 1911 Gunsmith Barrel $115
• Install 1911 Hammer $25–45
• Install 1911 Trigger $25
• Install Grip Safety $35
• Open 1911 Ejection Port $45
• Polish 1911 Feed Ramp & Throat $45
• Tighten 1911 Slide $65

• Revolver

• Chamfer Revolver Barrel $45
• Chamfer Revolver Cylinder $45
• Correct End Shake $90
• Cylinder Timing $65–120
• Double Action Smoothing/Tuning $90–160
• Re Barrel Revolver $90
• Set Barrel To Cylinder GAP $90
• Traditional Double Action Smoothing/Tuning $115–225

• Rifle Work

• Assemble AR15 Lower Receiver $95–135
• Assemble AR15 Upper $45
• Assemble Ruger 10/22 $95–135
• Bolt Lug Lapping $45
• Chamber & Fit Barrel To Action $135
• Chamber And Replace Barrel $130–500
  Using high quality barrels from Shilien, McGowan, Lilja, Bartlein and others
• Chamber Casting $25
• Check Headspace $15
• Cut & Crown Barrel $95
• Install AR15 Gas Block $65–95
• Install Chambered And Threaded Barrel $45
• Install Extractor $35
• Install Oversize Firing Pin $25
• Install Receiver Sights $25
• Install Receiver Sights With Drilling $65
• Install Safety $35–135
• Install Winchester Mod 70 Safety $45
• Machine Bolt For SA Ko Type Extractor $90–120
  Part kit is 30.00, price varies with hardened bolt material
• Polish Chamber $30
• Rebarrel Remington, Winchester, And Similar With Threaded And Chambered Barrel W/O Extractor Cut. Price Baries With Difficulty Of Removing Barrel. $90–130
  Requires setting headspace. Barrels that have been threadlocked will either be rejected with a 30.00 minimum, or pulled at owners risk
• Rebarrel Savage Type Rifles Using Barrel Nut $65
  Requires setting headspace
• REM 700 Action Blue Printing Accurizing $150–200
  Chase receiver threads to align bore, face cut receiver, cut and lap recoil lugs; all done in linge with barrel and receiver common axis
• Remove Fouling $25–45
• Remove Live Round $90–180
• Remove Obstruction $25–45
• Remove Stuck Case $25–45
• Replace Remington Extractor $25
• Scope Mounting $45
• Scope Mounting With Drilling $65
• Set Back Barrel $90
• Thread Barrel For Muzzle Brake And Install Clocked Muzzle Brake $125–150
  Clocking can be set for shooters preference (e.g. 11 for left hand, universal for 12, or 1 for right hand). Muzzle brake is separate.
• Thread Barrel For Muzzle Brake And Install Universal Muzzle Brake (Not Clocked) $90–125
  Muzzle brake is separate. Price varies with barrel (e.g. removing old iron sight, not removing receiver, etc). Includes all calibers.

• Stock Work

• Glass Bedding $135–180
• Install Recoil Pad $45
• Install Sling Swivels $25
• Oil Or Lacquer Finish $360–495
• Pillar Bedding $135–160
• Spray Finish $270
• Stock Repair $90–180
  Simple crack pinning to stripping and raising dents

• .22 Rimfire Rifles

• Correct Feeding Problem $45
• Correct Headspace $65–130
  Varies with model
• Fix Firing Pin Chamber Dent $25
• Fix Trigger $65
• Install Extractor $35
• Polish Chamber $30
• Replace Firing Pin $35

• Shotgun Work

• Choke Work $35–115
• Correct Remington 1100 Feeding $45
• Fix Double Locking Block $45–115
• Fix In Hammer Firing Pin $90–115
  Hammers are priced individually.
• Fix Non Removeable In Frame Firing Pin $180
• Fix Removeable In Frame Firing Pin $45
• Headspace Correction On Pivot Barrels $90–200
• Increase Browning Auto 5 Ejector Throw $35
• Install Front Bead Sight On Plain Barrel $45
• Install Sling Swivels On Sxs Shotgun, Installation Only $40–60
  Swivel set is 35.00 extra
• Polish Chamber $30–50
  single barrel - double barrel
• Refit Double Hinge Pin $90
• Replace Firing Pin $45
• Replace Remington 1100 Gas Seal Or Similar $25
• Straighten Barrel $45
• Time Cartridge Stops $35
• Trigger Work $65
• Trigger/Sear Adjustment $65
  single barrel - double barrel

• Materials And Stock Items

• Fire Lapping Materials Kit $30–100
  Varies with caliber and type of process required.
• Simple Muzzle Brake (Cm Or Ss) $50–75
  
  Finish and caliber boring extra if needed

• Part Pricing

• Cerakote Finish Material $35
  Pricing is per color.
• Glass Bedding Epoxy $7
• High Efficiency Slotted Muzzle Brake Stainless (Not Final Bored For Caliber) $85
  
  I have to order these by barrel size and thread. 2-4 weeks lead time for parts. Finishes are additional. Provides maximum recoil reduction.
• Lot Extra Consumables $10
  During cleaning or other gunsmithing activities if extra stock items are required to finish the job (e.g. very dirty gun).
• Silver Solder $15
• Standard Muzzle Brake Stainless (Not Final Bored For Caliber) $55
  I have to order these by barrel size and thread. 2-4 weeks lead time for parts. Finishes are additional.
• Test Fire $20
  I will use either ammo that you provide or that you puchase from me.